Shopping basket

Your shopping basket is empty

Joe's No Flats - Yellow Gel Sealant 20L

(0)

Description

Fiber gel sealant for inner-tubes (not for tubeless system). Contains micro-fibers to prevent punctures in the tread up to 3 mm. Non-toxic, Long lasting and easy to install. Easy to use spout fits into all valves. For effective puncture resistance, add fresh sealant every 12 months. If you get a puncture, always SPIN the wheel to distribute the sealant. Recommended Amount for 1 26" or 29" inner-tube: 120 ml. 240 ml bottle is good for 2 bicycle wheels and 5 liter jerrycan is good for approximately 42 wheels.

Description

Fiber gel sealant for inner-tubes (not for tubeless system). Contains micro-fibers to prevent punctures in the tread up to 3 mm. Non-toxic, Long lasting and easy to install. Easy to use spout fits into all valves. For effective puncture resistance, add fresh sealant every 12 months. If you get a puncture, always SPIN the wheel to distribute the sealant. Recommended Amount for 1 26" or 29" inner-tube: 120 ml. 240 ml bottle is good for 2 bicycle wheels and 5 liter jerrycan is good for approximately 42 wheels.

In stock

€ 275,00

  • Klantenbeoordeling
  • Voor 17u besteld, dezelfde werkdag verzonden
  • Eenvoudig binnen 14 dagen retourneren

Specifications

  • Article code180906
  • EAN7290101180906
  • BrandJoe's no flats
  • ModelYELLOW GEL
  • Type of bikeE-Bike
  • Volume (ml)20000
  • KLeurnewYellow

Others also bought

  • Bike7 - Brake Cleaner 500ML

    Removes dirt, oil and brake fluid from the brake blocks, callipers and disks for optimal safety. Spray onto surface. Allow to penetrate. Spray off loose dirt with the powerful Brake Cleaner spray and/or rub clean.
    In stock
  • Bike7 - Deblock 500ML

    Badly-maintained bicycles require another approach. You often have to deal with rusted bolts and components. For this you need powerful products that make disassembly easier. Deblock is a rust-dissolving penetrating oil that deals with the worst kind or dirt. This product finds it ways into the most unreachable nooks and crannies thanks to its high penetration. To loosen parts that have rusted solid. Spray Deblock from a distance of 20 cm and give it several minutes to work its way in before starting disassembly.
    In stock
  • Bike7 - Pro Seal 1 Liter

    Pro Seal is a latex emulsion that quickly seals holes in all tubeless tires, whether mountain bike or racing tires. Pro Seal is applied through the valve or poured directly into the partially disassembled tire and provides effective immediate repair. Can be used in both "Tubeless" and "Tubeless ready" tires. Closes holes up to 8mm. Compatible with CO2 cartridges. Contains natural Latex, is not corrosive or toxic. Pressure resistant up to 7 bar / 100 PSI. INSTRUCTIONS: Disassembled tire: New tire: clean the inside with Bike7 Degrease and wipe. Install one side of the tire and keep the wheel straight. Shake the bottle vigorously and pour the required amount directly into the tire, keeping the bottle upright. Assemble the tire completely. Mounted tire, with the 125 ml bottle: Remove the valve core and place the wheel, valve down, vertically without pressing the rim against the ground. Shake the bottle vigorously, cut the spout 2mm from the end and pour the required amount directly through the valve while keeping the bottle upright. Reassemble the valve. Inflate the tire: Gently turn the wheel one full turn. Inflate the tire until it fits properly. Turn and wiggle the wheel for ± 1 minute for a good distribution of the Bike7 Pro Seal. Adjust the tire to the desired pressure. Road tire (23-30 mm): 60 ml / tire and MTB tire (29 ", 2.0-2.4): 100 ml / tire. A larger amount is recommended for larger tires. A larger amount of product can be used for better protection. Effective life between 3 and 8 months, depending on the circumstances. Check the fluidity of the product every month and top it up if necessary.
    In stock
  • Bike7 - Pro Seal 125ML

    Pro Seal is a latex emulsion that quickly seals holes in all tubeless tires, whether mountain bike or racing tires. Pro Seal is applied through the valve or poured directly into the partially disassembled tire and provides effective immediate repair. Can be used in both "Tubeless" and "Tubeless ready" tires. Closes holes up to 8mm. Compatible with CO2 cartridges. Contains natural Latex, is not corrosive or toxic. Pressure resistant up to 7 bar / 100 PSI. INSTRUCTIONS: Disassembled tire: New tire: clean the inside with Bike7 Degrease and wipe. Install one side of the tire and keep the wheel straight. Shake the bottle vigorously and pour the required amount directly into the tire, keeping the bottle upright. Assemble the tire completely. Mounted tire, with the 125 ml bottle: Remove the valve core and place the wheel, valve down, vertically without pressing the rim against the ground. Shake the bottle vigorously, cut the spout 2mm from the end and pour the required amount directly through the valve while keeping the bottle upright. Reassemble the valve. Inflate the tire: Gently turn the wheel one full turn. Inflate the tire until it fits properly. Turn and wiggle the wheel for ± 1 minute for a good distribution of the Bike7 Pro Seal. Adjust the tire to the desired pressure. Road tire (23-30 mm): 60 ml / tire and MTB tire (29 ", 2.0-2.4): 100 ml / tire. A larger amount is recommended for larger tires. A larger amount of product can be used for better protection. Effective life between 3 and 8 months, depending on the circumstances. Check the fluidity of the product every month and top it up if necessary.
    In stock
  • Reviews

    Recommended accesories

    • Joe's No Flats - Yellow Gel Sealant 240ML

      Fiber gel sealant for inner-tubes (not for tubeless system). Contains micro-fibers to prevent punctures in the tread up to 3 mm. Non-toxic, Long lasting and easy to install. Easy to use spout fits into all valves. For effective puncture resistance, add fresh sealant every 12 months. If you get a puncture, always SPIN the wheel to distribute the sealant. Recommended Amount for 1 26" or 29" inner-tube: 120 ml. 240 ml bottle is good for 2 bicycle wheels and 5 liter jerrycan is good for approximately 42 wheels.
      Out of stock