Highly effective cleaner and degreaser for chains, derailleurs, cassettes and chainrings. Regular use will prolong transmission life. Apply and allow to soak in. Rinse thoroughly with water. After drying, re-lubricate chain.
Cleaning your bike after every ride can be a tedious affair. But with the right products you can do it in no time at all and even enjoy cleaning your bike. Good maintenance is indeed essential for keeping it in good condition. Clean has been specially developed to make this as easy as possible. You see the difference straight away. Quick and thorough cleaning of the handlebars, frame, fork, click-in pedals, wheels, ... . Removal of dried dirt, sweat, sand, dust, etc. from stainless steel, aluminium, titanium, lacquer, rubber, carbon fibre, ... . Lubricate all moving parts with Lubricate for optimal maintenance. Use an ordinary garden hose for the best result. No high pressure cleaner required.
After thorough cleaning you need to lubricate your bicycle. Most lubricants are not pressure-resistant. This means the lubricating effect is lost as soon as pressure is exerted. So choose durable lubrication with Lubricate. Lubricate is a transparent lubricant with PTFE to eliminate sustained friction. Lubricate Wet is an adhesive lubricant with high penetrating power for deep lubrication. The product also continues to have its effect after hosing off. Suitable for wet, greasy and muddy courses. Shake well before use! First clean the parts to be lubricated with Degrease, let it evaporate or dry with compressed air. To guarantee optimal, lasting lubrication, leave for 10 minutes after use before riding.
Pro Seal is a latex emulsion that quickly seals holes in all tubeless tires, whether mountain bike or racing tires. Pro Seal is applied through the valve or poured directly into the partially disassembled tire and provides effective immediate repair. Can be used in both "Tubeless" and "Tubeless ready" tires. Closes holes up to 8mm. Compatible with CO2 cartridges. Contains natural Latex, is not corrosive or toxic. Pressure resistant up to 7 bar / 100 PSI. INSTRUCTIONS: Disassembled tire: New tire: clean the inside with Bike7 Degrease and wipe. Install one side of the tire and keep the wheel straight. Shake the bottle vigorously and pour the required amount directly into the tire, keeping the bottle upright. Assemble the tire completely. Mounted tire, with the 125 ml bottle: Remove the valve core and place the wheel, valve down, vertically without pressing the rim against the ground. Shake the bottle vigorously, cut the spout 2mm from the end and pour the required amount directly through the valve while keeping the bottle upright. Reassemble the valve. Inflate the tire: Gently turn the wheel one full turn. Inflate the tire until it fits properly. Turn and wiggle the wheel for ± 1 minute for a good distribution of the Bike7 Pro Seal. Adjust the tire to the desired pressure. Road tire (23-30 mm): 60 ml / tire and MTB tire (29 ", 2.0-2.4): 100 ml / tire. A larger amount is recommended for larger tires. A larger amount of product can be used for better protection. Effective life between 3 and 8 months, depending on the circumstances. Check the fluidity of the product every month and top it up if necessary.
Pro Seal is a latex emulsion that quickly seals holes in all tubeless tires, whether mountain bike or racing tires. Pro Seal is applied through the valve or poured directly into the partially disassembled tire and provides effective immediate repair. Can be used in both "Tubeless" and "Tubeless ready" tires. Closes holes up to 8mm. Compatible with CO2 cartridges. Contains natural Latex, is not corrosive or toxic. Pressure resistant up to 7 bar / 100 PSI. INSTRUCTIONS: Disassembled tire: New tire: clean the inside with Bike7 Degrease and wipe. Install one side of the tire and keep the wheel straight. Shake the bottle vigorously and pour the required amount directly into the tire, keeping the bottle upright. Assemble the tire completely. Mounted tire, with the 125 ml bottle: Remove the valve core and place the wheel, valve down, vertically without pressing the rim against the ground. Shake the bottle vigorously, cut the spout 2mm from the end and pour the required amount directly through the valve while keeping the bottle upright. Reassemble the valve. Inflate the tire: Gently turn the wheel one full turn. Inflate the tire until it fits properly. Turn and wiggle the wheel for ± 1 minute for a good distribution of the Bike7 Pro Seal. Adjust the tire to the desired pressure. Road tire (23-30 mm): 60 ml / tire and MTB tire (29 ", 2.0-2.4): 100 ml / tire. A larger amount is recommended for larger tires. A larger amount of product can be used for better protection. Effective life between 3 and 8 months, depending on the circumstances. Check the fluidity of the product every month and top it up if necessary.
In stock
This product is not available at the moment.
Do you want to be informed about its availability? Please fill in your emailadress.
